Solidworks Drawing Delete Text Box

Overview

In the release of SOLIDWORKS 2016, in that location was an add-on to Drawings that allows the designer to modify the border of a default template called the Automatic Border Tool. Using the Automated Edge Tool, y'all tin can completely customize the edge to allow manufacturers and customers to hands read and interpret your technology cartoon. There are vi main categories of a drawing you tin can customize using the tool:

• Delete exisiting items from the default Canvas Format
• Zone size
• Margins and Borders
• Independent Border
• Zone Formatting
• Margin mask

Launching the Automatic Edge Tool

Follow the steps below and yous will exist able to alter the drawing edge of a default template:

• Right-click (RMB) in the centre of the cartoon and left-click (LMB) Edit Sheet Format as shown below in Figure 1 . This will take you to the Edit mode and evidence the Automated Border pick.

Figure one: Edit Sail Format option in the right-click drop down carte

• Correct-click (RMB) in the centre of the drawing and left-click (LMB) Automatic Edge… as shown below in Figure 2 . This will launch the Automatic Edge Holding Manager.

Effigy 2: Automatic Border selection in the right-click drib down card

Delete Existing Items from the Default Sheet Format

The showtime page of the Automatic Border Property Manager is to select entities from the drawing canvas to delete. The entities y'all select to be deleted volition be populated in the Delete List. Figure 3 and Figure iv bear witness before and after deleting the Proprietary and Confidential information from the default Championship Cake. Afterwards deleting unnecessary items from the drawing select to get to the next page of the Automatic Border Property Manager.

Zone Size

The distribution of the rows and columns can exist adjusted in the Zone Size options. Typically, Zone Sizes volition be dictated by the drafting standard used in the drawing (ex: ANSI, ISO, DIN, JIS, etc.) These values are well documented in engineering science handbooks and online. The Zone Size options are cleaved up into two sections; Distribution and Region. The Distribution is based on the Region option. 50mm from center sets the zone size to 50mm and centers the zones to the Margin or Sheet. Evenly sized distributes the Zone Size evenly based on the number Rows and Columns selected. Effigy 5 shows the selections for an ANSI Size-A Landsacape Drawing.

Figure five: ANSI Size-A Mural Cartoon Sheet Format Zone Size selections

Margins and Borders

The adjacent selection you lot can alter is the Margins and Borders. The Margin of an engineering drawing is the blank space betwixt the edge of the page and the Border. It tin can exist modified using the options boxed in cherry-red in Effigy vi .

The Border of an engineering science cartoon separates the cartoon view area from the Margin. The Line Way and Border Thickness tin can be modified using the drib-down options boxed in blue in Figure 6 . Selecting the checkbox next to Double-line border will brandish two outer border lines.

Figure 6: Margins (red box) and Border (blue box) options

Independent Border

Selecting the checkbox next to Independent Border will intermission the relationship between the Border and Margins. The Left, Right, Meridian, and Bottom Border options volition no longer be grayed out like to Effigy 7 beneath. You will now be able to modify the Edge independently of the Margins. The Border will yet maintain a human relationship to Zone Sizes.

Figure seven: Independent Border option selected

Zone Formatting

Zones in an technology drawing are helpful to locate specific regions of a drawing when communicating with manufacturers and customers. For example, if in that location is a Revision in the drawing that needs to be discussed the Zone callout (ex: B2) will easily allow both communicating parties to exist looking at the same region of the cartoon.

Zone Dividers

The starting time selection in the Zone Formatting section is Zone Dividers. Zone dividers do exactly what the name entails. They divide the zones of the drawing based on the number of rows and columns selected in the Zone Size section. The Zone Dividers can exist toggled on/off by using the check box next to Show zone dividers. Effigy 8 and Figure 9 show the Zone Dividers toggled on and off, respectively.

Zone Divider Line Fashion, Thickness, and Length

The Zone Divider Line Style and Thickness can be modified just similar the drawing Border. The Line Style of the Zone Divider tin exist inverse to dashed, dot-nuance, dash-dot-dot, etc. The Thickness of the Zone Divider can be inverse from 0.0071" – 0.0787" or a Custom Size. The Length of the Zone Divider tin can be modified to ensure they piece of work with the Margin settings. Ideally, you would similar to easily run across the Zone Dividers without having them hanging off of the page. Effigy 10 shows the a close up of the Zone Divider options.

Figure 10: Zone Divider options

Zone Labels and Font

The Zone Labels are the messages and numbers that make upward the Zones of the drawing. A1 would be the bottom right Zone shown in Effigy eight in a higher place. In the Zone Labels section, you tin can toggle on/off the column and rows callouts. Y'all can also modify the Altitude that the Zone Labels are offset from the Border. The Font of the Zone Labels can also be completely customized. The Font, Font Style, Height, and Effects can all be changed by selecting Font… All of the Zone Label options can be seen in Figure eleven below.

Effigy 11: Zone Labels options

Margin Mask

A Margin Mask is an area of the cartoon that hides the Zone Dividers and Zone Labels in the margins. This allows you to reserve a space for notes and assembly instructions within the drawing. To insert a Margin Mask select Add Margin Mask . You lot tin can drag, drop, and resize the Margins Masks. Figure eleven shows the light-bluish surface area where the Margin Mask area has been placed. Effigy 12 shows the finished drawing sheet template with the Margin Mask inserted.

In summary, the Automatic Border Property Manager is a very powerful tool that allows you to customize every aspect of the Canvas Format of a cartoon.  Now that you have created a custom Sheet Format of a drawing you can save it for future use.  To save the Sheet Fortmat, select File -> Save Sail Format…

strongthation.blogspot.com

Source: https://www.goengineer.com/blog/solidworks-drawings-automatic-border-tool

Share this post